SubaruPerformance

Subaru WRX 2015–2018 Oil Change with a Fumoto Drain Valve (FA20DIT)

Change the oil on a 2015–2018 WRX: drain warm oil from the 14 mm plug, install a Fumoto F-108N valve in its place for easier changes later, hand-tighten a genuine Subaru filter up top, refill with 5W-30 and check for leaks.

Black Friday & Cyber Monday CarPlay deals →

Change the oil on a 2015–2018 WRX: drain warm oil from the 14 mm plug, install a Fumoto F-108N valve in its place for easier changes later, hand-tighten a genuine Subaru filter up top, refill with 5W-30 and check for leaks. This 4 min guide covers the Subaru WRX 2015–2018; John uses 5W-30 with tools, parts links and the full.

Overview

The WRX is an easy car to change oil on. John uses Pennzoil Ultra Platinum 5W-30, which the description says was the top-rated oil for the FA20 in the NASIOC oil thread, with a genuine Subaru filter. He also adds a Fumoto valve so future changes need no tools at the drain. Run the engine about 20 minutes first, since warm oil drains faster. Lift the car and remove the 14 mm drain plug from the black oil pan, and let it drain. Lowering the jack so the car sits level helps it drain all the way. Thread in the Fumoto valve in place of the plug, snug it and give it the extra 1/8 to 1/4 turn with a suitable open-ended spanner. Then swap the filter on top of the engine. Hand-tighten the new filter. Use a filter wrench only to remove a stuck one. Fill it up, start the car, let it warm and check for leaks.

Vehicle & fitment

Product
Oil change kit: Pennzoil Ultra Platinum 5W-30 full synthetic, genuine Subaru oil filter 15208AA130, and a Fumoto F-108N engine oil drain valve
Shown on
John's 2015 Subaru WRX (FA20DIT), applies to 2015–2018 WRX

Always confirm fitment for your exact year and trim with the seller before buying.

Tools & parts

Tools

  • Jack and jack stands (or ramps)
  • 14 mm socket for the drain plug
  • Open-ended spanner for the final Fumoto tightening
  • Oil filter wrench (removal only)
  • Drain pan and funnel

Parts

  • Pennzoil Ultra Platinum 5W-30 full synthetic
  • Genuine Subaru oil filter 15208AA130
  • Fumoto F-108N drain valve

Video chapters

Step by step

  1. 1

    Supplies▶ 0:00

    Pennzoil Ultra Platinum 5W-30, a genuine Subaru filter, and a Fumoto valve to make the next change easier.

  2. 2

    Find the drain plug▶ 0:19

    With the car up, the drain plug is on the black oil pan and easy to spot. Remove it with a 14 mm socket and let the oil drain.

  3. 3

    Drain it warm▶ 0:42

    He ran the car about 20 minutes beforehand. Warm oil drains faster. Lowering the jack so the car sits level lets it drain all the way.

  4. 4

    Install the Fumoto valve▶ 1:16

    Plug the pan with the Fumoto valve instead of the stock plug. Screw it in, then tighten a further 1/8 to 1/4 turn with a suitable open-ended spanner.

  5. 5

    Change the filter up top▶ 1:18

    The filter is on top of the engine. Swap it for the genuine Subaru filter.

  6. 6

    Hand-tighten the filter▶ 2:47

    Always hand-tighten the new filter. Use a filter wrench only to remove a stuck one.

  7. 7

    Refill and check for leaks▶ 3:01

    Fill with oil, start the car, watch the oil temperature come up and check underneath for leaks.

FAQ

What vehicle does this install fit?

It is shown for the Subaru WRX 2015–2018; John uses 5W-30. Fumoto F-108N drain valve replaces the 14 mm drain plug (Amazon link from the description) Always confirm your exact year, trim and factory audio with the seller.

How long does the install take?

John's full video is 4 min. Plan on that much time for a careful DIY install, plus extra if you are new to dash work.

What tools do I need?

Tools called out in the guide: Jack and jack stands (or ramps); 14 mm socket for the drain plug; Open-ended spanner for the final Fumoto tightening; Oil filter wrench (removal only); Drain pan and funnel.

Where do I get the parts?

Use the buy links on this page for the unit and any harnesses John used. Some links are affiliate links.

Is this beginner-friendly?

The guide breaks the job into 7 steps with timestamps into the video. If you can remove trim panels carefully, you can follow along.

John's Subaru WRX

More photos →
Which taillight is your favorite? Digging through some photos, totally forgot I had this many taillights in one periodMeanThe time I tinted my taillights. Clear on the left, tinted in the right. I didn't like the look so I took it off the same day

Photos from @ngooyen on Instagram. Follow for more.

Full transcript

Show the full transcript (22 lines) +

0:00So we have the pens oil plat that we're gonna do. This is. the new bottle. It's the same thing

0:08530 is what you need for this car with the Subaru oil filter and the

0:13promoted valve to make it easier for the next range so nothing to it let's just get to

0:19it alright the right so let's get down here just a book right here you can't miss it

0:35it's black it's right here and you just unscrew it that's where you're gonna

0:41unfill the oil so

0:42so make sure it's clean after you take the 14 out just drain the oil, let it sit, the oil

0:48right now is warm because I started like 20 minutes ago so it's still warm it

0:52should be able to be clean and then we can we can swap it to the Pomoto which is

0:56super easy and just do the change the oil filter up top. I lowered the jack so it

1:01it can be more on an even surface. That way it can drain all the way in the

1:05the bottom and here's the oil filter not too shabby I'm gonna leave it on for here

1:16right now because I want to plug the bottom first with the Pomotovolve then I'll

1:23change out the filter. Here is the Pomotovolve being Japan and there's a

1:43it's got a screw it on

2:43I put all the oil back into the bottle and then some

2:47little key points I want to mention you always want to hand tighten the oil

2:51filter you can use an oil filter wrench but that's just I would just use it to

2:57remove it if it gets kind of stuck but always hand tighten right here again a hand

3:01this thing and let's just fire up alright so oil temperature seems to be

3:08okay it's hotter than the F up in here but I'm just gonna test it out make

3:14sure there's no leaks and I'll be back

Machine-transcribed from the full-length video and lightly cleaned (product names fixed). Watch the video for exact wording.

Next step

Related install guides