LightingAcura

How to Restore Yellow Headlights: Wet Sand, Polish and UV Seal (Acura RSX)

Fix yellow, swirled headlights for good on an Acura RSX: clean the lens, wet sand at 1000 then 1500 grit, polish with PlastX using a buffer, then seal with a UV coat and wax so the haze doesn't come back.

Black Friday & Cyber Monday CarPlay deals →

Fix yellow, swirled headlights for good on an Acura RSX: clean the lens, wet sand at 1000 then 1500 grit, polish with PlastX using a buffer, then seal with a UV coat and wax so the haze doesn't come back. This 4 min guide covers the Shown on an Acura RSX; the same wet-sand, polish and seal process applies to.

Overview

Toothpaste, bug spray, baking soda and store kits all give temporary results. John's method makes the lens clear by wet sanding, then seals it with a UV coat so the yellowing and haze don't return. First wipe the headlight down. Water makes it look clearer because it fills the scratches, but when it dries the scratches are still there. Wet sand the lens flat at 1000 grit, keeping it wet the whole time. Be careful near the paint and mask it off if you're unsure. Popping the hood helps. Step up to 1500 grit, wipe it clean, then polish out the fine scratches with Meguiar's PlastX, the least abrasive compound he has, on a buffer. Start gentle and only go more aggressive if you need to. The before-and-after is a huge difference in a few minutes per side. Finish with the UV sealant and wax so it stays clear.

Vehicle & fitment

Product
Headlight restoration: 3M Wetordry 1000 and 1500 grit sandpaper, Meguiar's PlastX polish, a dual-action buffer, Blue Magic lens restorer / UV sealant and Collinite wax
Shown on
Acura RSX (yellowed, swirled headlights); the method works on most plastic headlight lenses

Always confirm fitment for your exact year and trim with the seller before buying.

Tools & parts

Tools

  • Spray bottle or hose to keep the lens wet
  • Dual-action buffer with polishing pad
  • Microfiber towels
  • Painter's tape (optional, to mask the paint)

Parts

  • 1000, 1500 and 2000 grit wet/dry sandpaper
  • Meguiar's PlastX polish
  • UV coat / sealant
  • Wax
  • Rubbing alcohol

Video chapters

Step by step

  1. 1

    The problem▶ 0:00

    Yellowed, swirled headlights on an RSX. The method is a bit more labor, but quick, easy and effective.

  2. 2

    Clean the lens▶ 0:34

    Wipe it down. Water makes the lens look clearer because it fills the scratches, but once it dries the scratches are still there.

  3. 3

    Wet sand at 1000 grit▶ 0:52

    Sand the lens flat, keeping it wet at all times. Be careful not to hit the paint. Mask around the lens if you're not comfortable, and pop the hood for better access.

  4. 4

    Step up to 1500 grit▶ 1:53

    Move from 1000 to 1500 grit, then wipe the lens clean with a wet towel.

  5. 5

    Polish with PlastX▶ 2:16

    Polish out the fine scratches with Meguiar's PlastX on a buffer. It's the least abrasive compound, so start there and only go stronger if needed. Wipe off the compound with a towel.

  6. 6

    Seal it▶ 2:52

    The lens is clear after polishing. The next step is a UV sealant and wax so the haze doesn't come back.

  7. 7

    Before and after▶ 3:04

    A huge difference, and it doesn't take long.

FAQ

What vehicle does this install fit?

It is shown for the Shown on an Acura RSX; the same wet-sand, polish and seal process applies to most polycarbonate headlights. Mask the paint around the lens if you're not used to sanding near it Always confirm your exact year, trim and factory audio with the seller.

How long does the install take?

John's full video is 4 min. Plan on that much time for a careful DIY install, plus extra if you are new to dash work.

What tools do I need?

Tools called out in the guide: Spray bottle or hose to keep the lens wet; Dual-action buffer with polishing pad; Microfiber towels; Painter's tape (optional, to mask the paint).

Where do I get the parts?

Use the buy links on this page for the unit and any harnesses John used. Some links are affiliate links.

Is this beginner-friendly?

The guide breaks the job into 7 steps with timestamps into the video. If you can remove trim panels carefully, you can follow along.

Full transcript

Show the full transcript (18 lines) +

0:00yo look at those Swirls and yellow headlights we're going to polish these headlights today and show you the steps that I take for a quick and easy effective way uh a little more labor intensive but a good way to clean up

0:16these yellow headlights on this RSX stay tuned with this RSX the first step is going to be just don't wipe it down and you kind

0:34Notice when you put water on it, it kind of vicks the lens more see-through, it's because the water is kind of getting inside those scratches, so it kind of masses the look, so it'ss getting a lot better, just because you wipe it down, but when the water evaporates, the scratches are going to still be there.

0:52, so what we're going to do is we're going to sand these headlights, you could master on the area and stuff like that, but I'm just going to do it raw and just rely on my skills.

1:01raw and just rely on my skills just going to sand all this down and um get it pretty flat and then just going to buff it out when you do this you want to make sure you get the water um you want to

1:16keep it Lube at all times and just be careful to hit the paint that's where it's going to take skills I recommend you guys masking it out if you guys aren't familiar I'm actually going to buff the whole car too so I'm going to remove any squirrels anyways if it scratches thing but with this car right

1:31here the bumper is kind of pulled out um you can pop a hood to make it

1:49[Music] easier all right so we increased the grit level from 1,000 to 1500 um now I'm just going to buff it make sure you wipe it it's wet right

2:04It's wet right now, I just wiped it with a wet towel, we're going to polish all these small little micro tangs.

2:16here, I the plastic X, it's the least abrasive one, I have more aggressive compound, let's start with the least aggressive, be safe.

2:26Towel to wipe off the compound.

2:39towel to wipe off the compound woo look at that bad boy holy so check it out boys and girls the

2:55headlight is now buffed and I didn't even throw a sealant or wax yet which I will that's a step you guys have to do next and this is the before huge difference they didn't take too much long they didn't take too long

3:01That's the step you guys will do next.

3:04And this is the before, huge difference, didn't take too much long, didn't take too long, and you can get results like this.

3:13Does that not look good?

3:18Let me know if you guys have any questions on this, and if you guys need tips on the materials I use, I'll put the links on the below.

3:27Thank you guys for watching, peace.

Machine-transcribed from the full-length video and lightly cleaned (product names fixed). Watch the video for exact wording.

Next step

Related install guides