4th Brake Light Install on a Subaru BRZ (Matching Valenti Revo Tail Lights)
Add a rear 4th brake light to a US-spec BRZ: drop the stock reverse light (two clips and two 10 mm bolts), route the new harness through the rubber grommet, tap brake and parking power from the tail light, then mount it on the included screw-in tabs.
Full video (11 min): 4th Brake Light install on Kim's BRZ 2016 MT · John's YouTube channel
Get the parts
- Posi-Tap / wire tap connectors: Generic pickGeneric pickSearch on Amazon ↗
- 10 mm socket set: Generic pickGeneric pickSearch on Amazon ↗
As an Amazon Associate I earn from qualifying purchases. Some links are affiliate links.
Add a rear 4th brake light to a US-spec BRZ: drop the stock reverse light (two clips and two 10 mm bolts), route the new harness through the rubber grommet, tap brake and parking power from the tail light, then mount it on the included screw-in tabs. This 11 min guide covers the Rear center reverse light location on the.
Overview
Kim wanted a 4th brake light that matches her Valenti Revo tail lights, and she helps John install it. The new light comes with its own harness. US-spec BRZs don't have brake and parking power in the center light, so the tail light comes out to tap those circuits. The stock reverse light is held by two clips and two 10 mm bolts, and its bulb sockets unscrew. The new harness follows the factory reverse wire through a rubber grommet. They trimmed the grommet a little because they didn't have a repin tool, then stretched it to push the wires through. After testing brake and parking, they moved the stock harness clips to the new harness so the wires can't flop around and hit the exhaust. The light mounts with the new screw-in tabs that come with it, which hold better than the factory ones. The bottom tab goes in first. On their light the blue wire joined the green wire and the brown joined the red. Check the instructions for your light. It took about an hour while filming. The red is about 80% of a match to the Revos, and they picked it over the Valenti version because that one has chrome around the reverse light.
Vehicle & fitment
- Product
- Aftermarket all-red rear 4th brake / reverse light with harness (the brand isn't named in the video)
- Shown on
- Kim's 2016 Subaru BRZ with Valenti Revo tail lights
- Rear center reverse light location on the 2013+ Subaru BRZ (same rear bumper as the Scion FR-S / Toyota 86)
- US-spec cars don't have the brake and parking function in that spot, so those two wires are tapped from the tail light
Always confirm fitment for your exact year and trim with the seller before buying.
Tools & parts
Tools
- 10 mm socket
- Trim tool
- Wire taps or crimp connectors
- Electrical tape
- Small knife (to trim the grommet if you don't have a repin tool)
Parts
- 4th brake light with harness and screw-in mounting tabs
Step by step
- 1
Compare with the tail lights▶ 0:20
Hold the new light up to the Valenti Revos to check the match.
- 2
Pull the tail light▶ 2:00
Remove the tail light so you can tap brake and parking power. US-spec lights don't have it at the center light.
- 3
Remove the stock reverse light▶ 2:30
Two clips and two 10 mm bolts hold it in. Unscrew the two bulb sockets.
Tip: Be careful: the clearance under the bumper is tight.
- 4
Route the harness▶ 3:50
Follow the stock reverse harness through the rubber grommet and push the new wires through it. They trimmed the grommet a little because they didn't have a repin tool.
- 5
Test▶ 4:55
Check the brake and parking functions before closing everything up.
- 6
Transfer the clips▶ 5:33
Move the two stock harness clips to the new harness so it can't hit the exhaust.
- 7
Mount the light▶ 6:00
Use the included screw-in tabs instead of the factory ones. Start with the bottom tab, then work the light in.
- 8
Finish the wiring▶ 7:52
On this light: blue to green, brown to red. Wiring the extra function is optional. Check your light's instructions.
- 9
Result▶ 8:29
About an hour with filming. All red and about 80% matched to the Revos.
Wiring notes
- Brake and parking power tapped from the tail light (US-spec cars lack them at the center light).
- On this kit: blue to green, brown to red. Confirm with your light's instructions.
- Reverse light uses the stock reverse plug.
Get the parts
- Posi-Tap / wire tap connectors: Generic pickGeneric pickSearch on Amazon ↗
- 10 mm socket set: Generic pickGeneric pickSearch on Amazon ↗
As an Amazon Associate I earn from qualifying purchases. Some links are affiliate links.
FAQ
What vehicle does this install fit?
It is shown for the Rear center reverse light location on the 2013+ Subaru BRZ (same rear bumper as the Scion FR-S / Toyota 86). US-spec cars don't have the brake and parking function in that spot, so those two wires are tapped from the tail light Always confirm your exact year, trim and factory audio with the seller.
How long does the install take?
John's full video is 11 min. Plan on that much time for a careful DIY install, plus extra if you are new to dash work.
What tools do I need?
Tools called out in the guide: 10 mm socket; Trim tool; Wire taps or crimp connectors; Electrical tape; Small knife (to trim the grommet if you don't have a repin tool).
Where do I get the parts?
Use the buy links on this page for the unit and any harnesses John used. Some links are affiliate links.
Is this beginner-friendly?
The guide breaks the job into 9 steps with timestamps into the video. If you can remove trim panels carefully, you can follow along.
Full transcript
Show the full transcript (65 lines) +
0:00I have something
0:20Actually from this yeah, it's actually like the same
0:30So, comparing that to the
1:00And there's the lard harness, Bada Bing Bada BOOM, it's gonna match your rear so much
1:30Let's get ready for the install
2:00Alright, just get that out of there
2:11and the tail light so we can tap in the brake and then the parking because the stock
2:23U.SDM ones don't have that
2:30So there's two clips and two-tens and that's the only thing that's holding this bad boy in
3:00Hello, so we just got 110 now and I'm trying to remove the second one
3:17Be careful
3:38You justf got to unscrew these two sockets out I'll try I could have done it while it was up
3:44there, but I didn't have enough clearance
3:50Right here that's where the stock harness that was for the reverse
3:55So we just have to unclip it and then if you follow it, there's actually
4:01a little rubber garment that goes from this wire all the way here and then it goes
4:06straight down. So that's how the wires got to take it off. So what are you doing right now?
4:14Try to get this clip into the hole so I can push all the wire all the way in.
4:22We did trim the rubber garment because we don't have a re-pin tool
4:26We just cut it a little bit and then we're just going to squeeze it up
4:30And um I'm just going to force it in. I'm just going to force. I'm just going to stretch it a little bit
4:41A little bit harsh. There's a lot of what? Nothing. Just try to get it in here so. I'll give you a hand.
4:55So this is the brake light function right there and then this should be the parking
5:07And they matched the tail lights. They're almost like very close. I would say it's like 80% there.
5:20Awesome. So all on the lights work
5:24Let's just do the install and we should be done.
5:33So the stock harness has these two clips. What we're going to do is transfer it to the new ones.
5:39That way the wiring harness is not going back and forth hitting
5:41hitting the exhaust or whatever. So it's in there securely. So there's two mounting points.
5:47One's like right here and the one's right there.
5:55So we've got the wiring in there. We're just going to put this bad boy on a on the bottom.
6:00We're going to reuse the uh not reuse but there's there's new tabs that comes with.
6:05So we're not going to use the factory ones. We're going to use the one included.
6:08These are screwed so they're actually more secured and yeah we're going to pop it out.
6:13Pop it in there. Let's do it. Okay my neck. My double chin.
6:21Not a young man anymore. Alright so putting this bad boy in.
6:28You want to match with the bottom tab so the anchor's on there and then we can work it in.
6:35So bottom tab.
6:47Peer it up pull it.
6:50Oh yeah. Oh yeah.
6:56We don't need to reuse protection.
6:59Wow.
7:04Take it off. Oh careful you don't want to scratch it at this point.
7:13Is it working? Yes.
7:19It's all over. Perfect Stanley's right in line.
7:23So we have to wire the this light. If you don't want to wire it's okay.
7:30We don't have to and then we do this.
7:31You want the third brake light or the fourth brake light?
7:37We have to talk because we can't see you not.
7:41Can you say yes? Yes.
7:44Is that better?
7:45Yeah.
7:49Love you.
7:52The blue wire goes with the green wire. The brown wire goes with the red wire.
8:03That's it.
8:03That's it? Yeah it's on.
8:14It's on.
8:15That's on. That's on. Everything's is working.
8:29How long did it take us babe? How long did it take you to do it?
8:33Probably an hour. An hour? Yeah we're filming everything.
8:41It's very clean. I prefer these lights over the Valenti lights because of the way they look.
8:48It's all red. Yeah it's all red and the Valenti ones they had the chrome pieces on the bottom
8:54which I don't think would match the Valenti rebels.
8:57I think the the Valenti ones they have the red one but I
9:27got
Machine-transcribed from the full-length video and lightly cleaned (product names fixed). Watch the video for exact wording.
Next step





