LightingSubaru

LED License Plate Bulb Swap on a Subaru BRZ (5-Minute Mod)

Replace the BRZ's yellowish license plate bulbs with cheap white T10 / 194 LEDs: pop out the light housings, swap the bulbs, and push them back in. It takes about five minutes.

Black Friday & Cyber Monday CarPlay deals →

Get the parts

As an Amazon Associate I earn from qualifying purchases. Some links are affiliate links.

Replace the BRZ's yellowish license plate bulbs with cheap white T10 / 194 LEDs: pop out the light housings, swap the bulbs, and push them back in. It takes about five minutes. This 2 min guide covers the License plate lights on the Subaru BRZ with tools, parts links and the full video.

Overview

Kim didn't like the dull, yellow look of her BRZ's license plate lights, so she swapped them for bright white LEDs that match the reverse lights. The plate light housings come out once you remove the small pins, the old bulb pulls out, and the LED pushes in. In the side-by-side, the LED side is brighter and wider than the stock bulb. The whole job took less than five minutes, and the LEDs cost about five bucks for two. It brightens up the license plate a lot, and now the whole rear of her car is LED. It's a perfect first mod if you want something cheap and easy.

Vehicle & fitment

Product
Yorkim T10 / 194 LED bulbs, 6500K white
Shown on
Kim's 2016 Subaru BRZ Limited (6-speed manual)

Always confirm fitment for your exact year and trim with the seller before buying.

Tools & parts

Tools

  • Small flat-head screwdriver or trim tool

Parts

  • 2 x T10 / 194 white LED bulbs

Step by step

  1. 1

    Why swap▶ 0:00

    The stock license plate light looks dull and yellow. White LEDs look cleaner and match the reverse lights.

  2. 2

    Remove the housing▶ 0:33

    Take out the small pins that hold the license plate light, then pull the housing out.

  3. 3

    Swap the bulb▶ 0:46

    Pull the old bulb and push in the LED. Compare both sides: the LED is brighter and wider.

    Tip: If an LED doesn't light, flip it 180 degrees (only needed if it's polarity-sensitive).

  4. 4

    Reinstall and check▶ 1:11

    Put the housing back. About five minutes for the whole job.

  5. 5

    Result▶ 1:19

    It brightens the plate a lot, and two LEDs cost about five bucks. A perfect cheap, easy mod.

Get the parts

As an Amazon Associate I earn from qualifying purchases. Some links are affiliate links.

FAQ

What vehicle does this install fit?

It is shown for the License plate lights on the Subaru BRZ. Uses T10 / 194 wedge bulbs (the LED pack in the description is a 194 / 168 / W5W size) Always confirm your exact year, trim and factory audio with the seller.

How long does the install take?

John's full video is 2 min. Plan on that much time for a careful DIY install, plus extra if you are new to dash work.

What tools do I need?

Tools called out in the guide: Small flat-head screwdriver or trim tool.

Where do I get the parts?

Use the buy links on this page for the unit and any harnesses John used. Some links are affiliate links.

Is this beginner-friendly?

The guide breaks the job into 5 steps with timestamps into the video. If you can remove trim panels carefully, you can follow along.

Full transcript

Show the full transcript (17 lines) +

0:00How does that make you feel the trunk lights I don't really like this color

0:16It looks a-. It looks a little dull to me so I'm going to change it out and switch it up with the brighter

0:21White color rather than a yellow color

0:25And we're about to do that in the night time

0:28Just so I can get a new look to it

0:33Yeah, so there's slowly these little pins you just have to remove

0:46So here's what it looks like with a comparison. There's the yellow light and then we just put on the LED

0:53I think it looks way better with how it looks on the right side than on the left side a

1:04It's a lot wider and that will match your reverse lights and stuff

1:08Yeah, I'm tired of the yellow

1:11So this was pretty much a very easy mod it's only five minutes

1:17to do

1:19The complete look I'm really satisfied with it. It really brightens up the license plate a lot better than the other lights that I had

1:27And it's really

1:28Really really cheap

1:29cheap they're about five bucks just for two LED's I think if you guys want to go for

1:35and easy to do mod this mod would be perfect

Machine-transcribed from the full-length video and lightly cleaned (product names fixed). Watch the video for exact wording.

Next step

Related install guides